JD-603
Roller Conveyor Metal Detector
Boxed and bagged products are frequently transported on roller conveyors during the production and packing process. Despite this, in-line metal inspection is still required for these lines. The issue is with the connection: the introduction of a belt-type detector into a roller line necessitates the addition of transfer points, and each transfer point is a potential location for product to become stuck, tip, or slow down.
The JD-603 roller conveyor metal detector is designed to be directly integrated with your existing roller system, as it is a roller conveyor.
- Detection Accuracy: Iron (Fe) ≥ 0.8 mm;
- Copper (Cu) ≥ 1.0 mm;
- Stainless Steel (SUS304) ≥ 1.5 mm
- Direct connection to roller lines. The product is mechanically transported from your line to the inspection area and beyond, as there is no belt transfer in between.
- Reduced Conveying Resistance. Smooth rollers reduce sliding friction and facilitate the conveyance of cartons and cases.
- Appropriate for cartons and containers. Designed to accommodate packaged and bagged products, as opposed to loose items on a belt.
The detector detects fluctuations in the electromagnetic field as products traverse the aperture. The system initiates an alarm or an automatic rejector to address the non-conforming product when metal is detected.
| Item | JD-603 Roller Conveyor Metal Detector |
| Detection principle | Electromagnetic induction |
| Detectable metals | Iron (Fe), copper (Cu), stainless steel, etc. |
| Construction | SUS304 stainless steel; SUS316 on request |
| Line height | 700 mm |
| Aperture size | W 400 × H 100 mm |
| Detection sensitivity | Fe ≥0.8 mm; Cu ≥1.0 mm; SUS304 ≥1.5 mm |
| Performance | Actual performance is confirmed by sample testing and depends on product height, packaging material, product temperature and humidity, and conveyor speed. |
| Conveyor speed | Fixed 20 m/min; adjustable 15–30 m/min (custom speeds on request) |
| IP rating | IP65 standard: dust-tight, protected against water jets, and easy to clean. IP66 / IP69K available for frozen food, meat processing and other high-humidity environments. |
| Power | Single-phase 220 VAC or 110 VAC, 200 W |
-
Pusher RejectorHeavier, stably packed products: vacuum-packed meat, frozen foods, bread, pharmaceutical packs. A pneumatic cylinder pushes the rejected product off the main conveyor.
-
Air-Blast RejectorLight products on fast lines: tea, seasonings, small food pouches.
A high-speed air jet blows the rejected product clear of the conveyor. -
Flap RejectorMedium-weight products whose packaging must stay intact: chocolate boxes, cartoned foods, frozen packs. A flap changes the product's conveying direction, diverting it smoothly without collisions.
-
Flipper RejectorSmall to medium packs: biscuits, tea, pharmaceutical packs. A flipper sweeps the rejected product off the main conveyor.
-
Mid-Section Lift RejectorVacuum-packed and high-value foods where appearance and packaging matter. The middle conveyor section raises or lowers so the product leaves the line gently, minimizing impact and pack damage.
-
End-of-Line Lift RejectorHeavy products that need their packaging protected: steaks, large food bags, gift boxes. The end conveyor section raises or lowers to change the product's direction.
-
Conveyor Stop AlarmFlour sacks, rice bags and other large-format products. The conveyor stops and an alarm sounds so an operator can remove the product by hand.
Most providers list fewer than seven possibilities. The practical benefit is that the reject method may be tailored to the pack rather than the pack being pushed onto whatever rejector is available, which is especially important for vacuum packs, gift boxes, and other products where a rough rejection harms salable goods.
- Aperture size
- Roller conveyor width and length
- Reject collection device
- Adjustable conveyor speed
- IP65 / IP66 / IP69K protection
- Automatic rejector
- SUS304 / SUS316 stainless steel construction
- Audible and visual alarm
















